Doc inlet temp during regen.

11. After the low temp ATD regeneration has run for 20 minutes, monitor the DOC outlet temperature sensor reading. Is the DOC outlet temperature sensor reading within 25°C (45°F) of the DOC inlet temperature sensor? a. Yes; replace the HC doser block. Refer to section "Removal of the Hydrocarbon Doser Block ". Verify repair. b.Jan 18, 2020 · Mack MP8 regen issues. 2012 CXU613 with 2012 fault codes so it's not a 2013. Truck arrived at the shop at the beginning of the week. Soot load was level 5. performed a parked regen. DOC inlet temp was bias. DPF outlet temp stayed above inlet temp during regen. Right away I noticed that the DOC inlet temperature reading was at 662 F (default max value as I found out) @ 1.7V, yet the outlet temperature was 419 F @ 1V . These thermo-couples run on 5V and generally have a much larger spread between temperature/voltage correlation. Now it was time to let the data talk.Once the nozzle was cleaned out it would do the regen and the high soot level code went inactive. I'm working on an 08 Western Star with a 60 series Detroit with EGR and DPF. It is a 06R0998711 engine. It has an active 3719 High Soot Level code. The engine runs for about 2 minutes and then shuts down.

temperature sensor). This phase will occur during all of the selected sub tests. AHI dosing will occur whether or not the AHI subtest is selected in order to meet target DOC outlet temperature (measured by the T2 temperature sensor) and SCR average temperatures and bring the NOx sensors online faster. Operation failure during Heating EATS phase:Temperature should begreater than 100 C (212 F) prior to parked regeneration initiatesand runs indefinitely. (IntakeThrottleonSeries60,DD15,andMBE 4000 or Exhaust Flap onMBE 900 does NOT close, andthereisnoHESTL ampafter25minutes.)Engine in smoke control modeMonitor smoke control status during regen. Smoke controlstatus should be Inlet ...7. Start the engine and run a Parked Regen. Monitor DOC inlet pressure and engine speed during the regen. Compare your DOC inlet pressure reading to the screen shots below to identify a possible cause of the fault code. a. If the DOC inlet pressure starts out high above 10 kPa (1.45 psi) and decreases during the parked regen, this

Got a 2018 Mack MRU with an MP7. Truck has had regen issues since we got it new, been to the dealership multiple times but Mack says they can’t duplicate the issues. Active codes as of right now. P103C00 P20EE00 P046C64 P24F700. Truck is in derate requesting a Sulfur regen. During the regen the Nox inlet is at 1026 PPM and outlet is 1773 PPM.Got a 2018 Mack MRU with an MP7. Truck has had regen issues since we got it new, been to the dealership multiple times but Mack says they can’t duplicate the issues. Active codes as of right now. P103C00 P20EE00 P046C64 P24F700. Truck is in derate requesting a Sulfur regen. During the regen the Nox inlet is at 1026 PPM and outlet is 1773 PPM.

Yes; Go to step 14. b. No; Refer to section "Unable to Start a Parked Regeneration". 14. Using DiagnosticLink, monitor DOC inlet temperature. Does the ...mixture during a Regen process of the Aftertreatment system. The ITV is common for all medium duty MaxxForce engines. Exhaust Gas Temperature (EGT). Sensor.The forced regen still shows the DOC temp close to the DPF intake temp and the DPF outlet temp stays around 550-600 but the new thing is that forced regen …11. After the low temp ATD regeneration has run for 20 minutes, monitor the DOC outlet temperature sensor reading. Is the DOC outlet temperature sensor reading within 25°C (45°F) of the DOC inlet temperature sensor? a. Yes; replace the HC doser block. Refer to section "Removal of the Hydrocarbon Doser Block ". Verify repair. b.a Diesel Oxidation Catalyst (DOC). Together, those products are effective at removing 99 percent of PM soot from the exhaust system using wall-flow substrates. As soot accumulates in the filter, a regeneration event will provide sufficient heat to oxidize the captured soot. The remaining ash is removed during regularly scheduled cleaning

The stage1 is before regeneration phase. The DOC inlet temperature, the DPF inlet temperature, and the DPF outlet temperature are sequentially lowered due to the heat loss. The stage2 is during regeneration phase. The DOC inlet temperature slightly reduces due to the vaporization heat of methanol.

The step response of DOC- out temperature can be acquired by injecting constant amount (i.e. 50 mg/s) of Diesel fuel into the exhaust pipe upstream of the DOC during different steady states (i.e. constant inlet temperature and mass flow rate of exhaust gas).

The Aftertreatment System Technician's Guide … NUMBER:08 ATS REF.:Listed in Table :ATSDATE:February 2008 SUBJECT: ADDITIONAL ENGINE WAS ADDEDPUBLICATION: DDC-SVC-MAN-0036 (7SE63)The Aftertreatment System Technician's Guide (DDC-SVC-MAN-0036) wasrevised to include theDD15 REQUIREMENTSA dded row toTable Maintenance …Engine Speed 1100 rpm (1275 rpm during first 12 minutes of regen then 1100 rpm for fuelmap ending in ZGS 999) Turbo Speed 45,000 – 60,000 (turbo is used to create pressure in the DD13 and DD15AT only) Fuel Cut Off Valve 100% (once DOC inlet temp reaches 536° F) Engine Torque Around 5% Actual Torque Load 15 – 18% (greater than 20% may ...02/02/2018 - Added temp differential test in step 2 01/03/2018 - Due to Cummins software changes, removed ROA test (previously step 2) DESCRIPTION This document will guide the user through resolving frequent regen issues on vehicles equipped with an ISB 6.7. SYMPTOM(s) Diagnostic Trouble Code(s) & Dashboard Indicator …If DPF outlet temp stays above the inlet temp then the DOC isn't working probably. Likely face plugged and allows a rich fuel mixture to burn inside DPF instead of DOC. DPF temp should be in the 1000-1100F range. If DPF temp reaches around 1300F, regen will shut down to prevent damage. There are 3 temp sensors but they might be …DOC is likely fuckered, you can never really visually see if a doc is fucked you just have to watch Temps during regen, ... Was able to push the regen after resetting the maintenance thing. A few minutes in, DOC intake temp is 580, Dpf intake is 435, and dpf outlet is 515. Think I may have a bad dpf intake sensor.

1 12-12-2015, 07:37 AM. cm871 low DOC temp won't reg to clear last code. Prostar ISX CM871 low DOC temp won't regen to clear last code. New turbo. New DOC. Cleaned DPF. Remove EGR and cleaned, no exhaust leaks. Engine temp 200 drg. Fan cycles.Engine in smoke control mode. Monitor smoke control status during regen. Smoke control status should be 0. DOC Inlet Temperature Sensor non-responsive. Monitor ...1 NUMBER: 2 ATS 07 S.M. REF.: Listed in Table 1 ENGINE: ATS DATE: April 2007 SUBJECT: UPDATES TO AFTERTREATMENT SYSTEM TROUBLESHOOTING PUBLICATION: 7SE63 The Aftertreatment System Technician's Guide has been revised. MANUAL REFERENCE Section 6.1, Mechanical Troubleshooting 9.1, SPN 3242/FMI , …9. Monitor DOC inlet and outlet temperatures. Are the temperatures within 25°C (45°F) of each other? 9.a Yes; Check valve lash and engine brake rocker lash. If either is out of adjustment, readjust the lash, perform a parked regeneration, and continue with the initial diagnostics that directed you to DOC inlet temperature will notJoined: Nov 2011. 6 10-28-2020, 10:36 PM. i have a volvo 2015 d13 with similar issue unit will start regen just fine. but when fuel doser comes up temp 1 is 520 temp 2 starts to climb really fast temp 3 doesnt follow and by the time temp 2 gets to 1000 ( withing 1 minute after doser starts to dose ) it turns off the fuel doser and turbo speed ...Throttle Valve Actual NOT USED DURING A PARKED REGEN Fuel Comp Pressure 85 - 92 psi ... DOC Inlet Temp 700 - 950 ° F DOC Outlet Temp 1050 - 1150° F DPF Inlet Pressure 0.5 psi - 1.0 psi DPF Outlet Pressure 0.01 psi to 0.9 psi Doser Injection Status gradual increase from 5% to 45% • DOC inlet temp must be at 525° F or higher to

During regen the temp doesn't get over 305. I thought it had to hit over 500 to kick on injector 7. ... We removed the DPF and DOC and got them baked and blew out. ... Constant regens. Two obd codes. Inlet trap pressure and particulate trap 1 ...

... inlet temperature sensor. Source: Cummins Quickserve. 2009 Cummins ISL Air Intake Overview ... DOC w/ DPF Emissions Control Systems Service. Exhaust, Intake and ...Tractor was towed in with engine warnings on, and in shutdown mode.Active faults for soot level high, and failed regen. due to temp. Inlet DOC temp only at 425, wont go high enough to start dosing fuel.Once the nozzle was cleaned out it would do the regen and the high soot level code went inactive. I'm working on an 08 Western Star with a 60 series Detroit with EGR and DPF. It is a 06R0998711 engine. It has an active 3719 High Soot Level code. The engine runs for about 2 minutes and then shuts down.Mar 15, 2017 · DPF regeneration temperature rising strategy chiefly considers two temperatures including DOC inlet temperature and the DPF inlet temperature. Temperature rising approaches is based on Great Wall 4D83 diesel engine whose performance parameters are listed in Table 1 and DPF experiment system is shown in Fig. 8. Secondary post injection (Post ... 13) Monitor DOC inlet temperature. It MUST be greater than 400°C (750°F). If it is not above 400°C (750°F), block off part of the radiator with cardboard. Be careful that coolant temperatures do not go high enough to cause a Check Engine ight.l 14) Continue to monitor the DOC inlet temperature to make sure it is greater than 400°C (750°F). COOLANT TEMPERATURE: 209F DOC INLET: 432F DPF INLET: 421F DPF OUTLET: 411F Last edited: Jun 10, 2017. 4vmach1, Jun 10, 2017. 4vmach1, Jun 10, 2017 #71 + Quote Reply. Trucking Jobs in 30 seconds. ... During one of the parked regen the delta-p set a out of range on the data monitoring, ...

What temp should doc inlet be during regen? Engine rpm should then become stable around 1275 rpm. 13) Monitor DOC inlet temperature. It MUST be greater than 400°C ...

The influence of far post injection in cylinder or downstream injection in the exhaust pipe on the DOC inlet temperature can be negligible (Chen, P. et al. (2014 ... Kim, Y. W., Van Nieuwstadt, M., Stewart, G., & Pekar, J. . Model Predictive Control of DOC Temperature during DPF Regeneration, SAE Technical Paper, No. 2014-01 ...

Jan 1, 2022 · The SCR temperature would be even lower than the DOC inlet temperature due to heat transfer to the DOC and DPF catalysts, both upstream of the SCR catalyst. During cold-start and other low exhaust temperature conditions such as idle and low load, higher NO x conversion can be achieved if thermal management strategies are implemented to increase ... During vehicle operation, active regeneration is performed when the accumulated soot and ash reach boundary limits. In this operation, the particulate soot is ...I have a MP8 not completing a regen, doser on 540 degrees dpf inlet 750 degrees dpf outlet 750 degrees When it reaches these temp the doser shuts off new doser, new dpf, cleaned doc, new ambient air temp sensor mack vin#8N001449 validation parked regeneration as noted in the troubleshooting. Troubleshooting for the 3711/31 fault should be completed to verify there is not an actual component issue causing low DOC inlet temperature such as a drifted DOC inlet temperature sensor or a sticking front Jake solenoid. 2018年9月18日 ... 3251 21 DOC Inlet / Outlet Pressure Not Plausible Without the ... i think most posts I have read regarding regen said you need to start at ...Jan 18, 2020 · Mack MP8 regen issues. 2012 CXU613 with 2012 fault codes so it's not a 2013. Truck arrived at the shop at the beginning of the week. Soot load was level 5. performed a parked regen. DOC inlet temp was bias. DPF outlet temp stayed above inlet temp during regen. Tue 11/28. 90° /76°. 65%. Times of clouds and sun with a couple of showers. RealFeel® 98°. RealFeel Shade™ 95°. Max UV Index 5 Moderate. Wind ENE 2 mph.Was given log file from last completed regen on the truck 10 days earlier. Comparing the 2, boost pressure and doc inlet pressure is slightly lower throughout regen. dpf out temp reaches above 1200 but doc out temp is above 1000 as well. Will upload if someone wants to comparea. If the DOC inlet pressure starts out high above 10 kPa (1.45 psi) and decreases during the parked regen, this indicates the DPFs were plugged and the parked regen cleared them. Go to step 10. b. If the DOC inlet pressure starts above 6 kPa (0.8psi), and stays high, the DOC is considered plugged. Go to step 11. 3 09-15 All information subject ...CM871 High DOC temp during regen [Server Time: 10/15/2023 05:21:32 am] This Forum is English-Only!!!,... Donations help keep the lights on around here, …Mack MP8 regen issues. 2012 CXU613 with 2012 fault codes so it's not a 2013. Truck arrived at the shop at the beginning of the week. Soot load was level 5. performed a parked regen. DOC inlet temp was bias. DPF outlet temp stayed above inlet temp during regen.

Save. ClickClick5 · #9 · Aug 7, 2015. EGT3 is the one you will want to watch for the regen. This is the post DPF temp probe. EGT2 is post DOC, and EGT1 is pre DOC. Normal driving, EGT3 will reach around 500-800F. You will know …The Aftertreatment System Technician's Guide … NUMBER:08 ATS REF.:Listed in Table :ATSDATE:February 2008 SUBJECT: ADDITIONAL ENGINE WAS ADDEDPUBLICATION: DDC-SVC-MAN-0036 (7SE63)The Aftertreatment System Technician's Guide (DDC-SVC-MAN-0036) wasrevised to include theDD15 REQUIREMENTSA dded row toTable Maintenance …Volvo D13 regeneration. we have couple of trucks on our fleet with the same problem. The forced regen would start but runs indefinetly and not continuously. T he exhaust temp rises to about 500, dpf inlet and outlet reaches up to 920 and then engine suddenly changes tone, shuts of the aftertreatment injector, dpf inlet and outlet temps drop for ...Instagram:https://instagram. matilda 1996 123moviessynclinesdancing turkey gif transparentif you want it take it lyrics If everything is checking out, then yes, the vanes are not adjusting properly. On just idling, the truck should be at a 160 degree engine temp and the exhaust should be around 520. As it gets warmer, the exhaust will get warmer. 180 degree truck should have a 600 degree exhaust at idle for this engine and the regen should start activating, the ...during an engine bench test in this study. Based on the dropped to idle (DTI) test, a test method is developed to determine the safe regeneration temperature of the DPF. The results show that when the inlet temperature of the DOC is more than 240 C, the DOC begins ignition and reaches the saferide nyucraigslist hart mi 11. After the low temp ATD regeneration has run for 20 minutes, monitor the DOC outlet temperature sensor reading. Is the DOC outlet temperature sensor reading within 25°C (45°F) of the DOC inlet temperature sensor? a. Yes; replace the HC doser block. Refer to section "Removal of the Hydrocarbon Doser Block ". Verify repair. b. daytona motorcycle accident a. If the DOC inlet pressure starts out above 10 kPa (1.45 psi) and decreases during a parked regen, this indicates that the DPFs were plugged and the parked regen has cleared them. Go to step 8. b. If the DOC inlet pressure starts above the pressure specified below and stays high, the DOC is considered plugged. Go to step 9. Table 1. Emissions ... Had a forced Regen done and off I went. 150 miles later the same code came back again. so I ignored it for another 250 miles and then second alert saying Air Intake system problem. Had a second Regen done and noticed Inlet manifold pressure was very high but as the regen was going on this issue reduced to normal levels.